13 Oct 15 debugging startup problems: trick of the day
Got an unfindable syntax error in startup?
We have the trick for you courtesy of JRF of the ITRC forums
/sbin/rc[102]: syntax error at line 188 : `”‘ unmatched
/sbin/rc1.d/S090hpvmguest[286]: /usr/bin/getconf: not found
/sbin/rc1.d/S090hpvmguest[286]: /usr/bin/grep: not found
/sbin/rc1.d/S105vparinit[63]: /usr/sbin/kcpath: not found
sh -vx /etc/rc.config 2>&1|more
+ fname=netconf
+ [ -f /etc/rc.config.d/netconf -a netconf != core -a netconf = netconf ]
+ . /etc/rc.config.d/netconf
/etc/rc.config[13]: Syntax error at line 188 : `”‘ is not matched.
Problem startup file in this case is netconf
Tags: forums.itrc.hp.com, hpux startup, init scrip problems, systems administration
12 Jul 11 Migrate VXVM booted system to LVM
From the HP-UX Veritas Administration guide, buried on page 106
This example shows how to create an LVM root disk on physical disk c0t1d0
after removing the existing LVM root disk configuration from that disk.
BOOTBG=$(vxdg bootdg)
vxprint -htg $BOOTDG | grep ^dm
dm rootdisk01 disk233_p2 auto 1024 142450592 –
dm rootmirr disk234_p2 auto 1024 142450592 –
# You get the boot disk from this command. Break off the s2 if you are using legacy devices you can use them or the agile SDF devices.
# You may need to use vxbrk_mirror to break the mirror. Make sure you know which disk you are booted from. Check syslog to be sure. setboot is not a good indicator.
# Due to a wordpress error I’ve been forced to take the path etc vx bin out of the commands. I will fix this when wordpress stops blowing chunks on this data. Where there are spaces there need to be slashes.
# etc vx bin vxdestroy_lvmroot -v c0t1d0
# etc vx bin vxres_lvmroot -v -b c0t1d0
The -b option to vxres_lvmroot sets c0t1d0 as the primary boot device.
As these operations can take some time, the verbose option, -v, is specified to
indicate how far the operation has progressed.
This command takes care of setboot and all details. Then just boot from the console.
This procedure does not remove VxVM software. The daemon still runs. But your system now boots LVM and that makes using Dynamic Root Disk (DRD) much easier.
Tags: Capacity Planning, forums.itrc.hp.com, high capacity volume group, Ignite-UX, patching, superdome, system migration
09 Jun 10 System I/O layout (EMC specific)
This is a script designed to document the layout of a system. It is EMC specific and requires the output of the inq command, which I store in /tmp/inq.txt
It can however be adapted to non EMC disk systems. It correctly shows the port/lba layout and status of network and fiber I/O the way it appears on the outside of the system. Two tables are included to permit lookups of the port/lba information. It has worked on blades, and is certified for rp8420 and superdome systems.
It has only been tested on HP-UX 11.31.
… please stand by….update in progress…
DF=”super.translate.dat”
MA=”router.macadd.dat”
typeset MYDIR=/var/tmp/syslayout
typeset MYPAGE=mypage
typeset MYDATA=mydata
typeset IDX_HTML=syslayout.html
writehtml (){
while [ $# -gt 0 ]
do
echo “<td>${1}</td>” >> ${IDX_HTML}
shift
done
echo “<tr>” >> ${IDX_HTML}
}
cat -<<!EOF > ${IDX_HTML}
<!DOCTYPE HTML PUBLIC “-//W3C//DTD HTML 4.0 Transitional//EN”>
<title>Dana IT Unix System documentation</title>
<BODY>
<TABLE style=”WIDTH: 100%; COLOR: rgb(0,0,0); TEXT-ALIGN: left” cellSpacing=2
cellPadding=2 border=0>
<TBODY>
<TR>
<td width=”200″><img
style=”border-width: 0px; margin: 0px; padding: 0px;” alt=”Dana”
src=”dana_logo.jpg”> </td>
<td style=”font-weight: bold;”><big><big>Dana
IT
Unix:
Documentation</big></big></td>
<TD style=”VERTICAL-ALIGN: top; TEXT-ALIGN: center” colSpan=7><BIG
style=”FONT-FAMILY: helvetica,arial,sans-serif”><BIG>Dana IT system I/O Layout.</BIG></BIG><BR></TD></TR>
!EOF
# colum layout # Path slot MAC Address lan ipaddress vlan linkstatus
sysname=$(uname -n)
this_cell=$(vparstatus -p $sysname -v |awk ‘/Boot processor/ {print $4}’ |awk -F’\.’ ‘{print $1}’)
# echo $this_cell
this_par=$(parstatus -c 0 |awk ‘/cell’$this_cell’/ {print $9}’)
nparname=$(/usr/sbin/parstatus -P |awk “/^$this_par/ {if(pname == 1) {print}};/Partition Name/ {pname=1}”|awk ‘/’$this_par’ / {print $6}’)
#echo “Diag nparname: ${nparname}”
complexname=$(/usr/sbin/parstatus -X |awk “/Complex Name/”)
cellind=”cell${this_par}”
nparinfo=$(/usr/sbin/parstatus -P |awk “/^$this_par/ {if(pname == 1) {print}};/Partition Name/ {pname=1}”)
# model needs to be determineed
OS=$(uname -r)
if [ “$OS” = “B.11.31” ]
then
mod=$(model | awk ‘{ print $5 }’)
else
mod=$(model | awk -F/ ‘{ print $3}’)
fi
hn=$(hostname)
this_cell=$(vparstatus -p ${hn} -v |awk ‘/Boot processor/ {print $4}’ |awk -F’\.’ ‘{print $1}’)
echo $this_cell
this_par=$(parstatus -c 0 |awk ‘/cell’$this_cell’/ {print $9}’)
/usr/sbin/parstatus -P |awk “/cell/ {if(pname == 1) {print}};/Partition Name/ {pname=1}”|awk ‘/’$this_par’ / {print $6}’
hn=$(hostname)
lhn=”${hn}.dana.com”
echo “Host name: ${lhn}”
writehtml “Host name:” ${lhn}
echo “Model number is: $mod”
writehtml “Model number:” ${mod}
#echo “<td>$complexname</td><td>$nparname</td><tr>” >> ${IDX_HTML}
writehtml “${complexname}” ${nparname}
echo “Model number is: $mod”
pbootpath=$(parstatus -p 0 -V |awk -F: ‘/Primary Boot Path/ {print $2}’)
echo “Primary boot path: ${pbootpath}”
writehtml “Primary boot path:” ${pbootpath}
#echo “<td>$complexname</td><td>$nparnam</td><tr>” >> ${IDX_HTML}
# echo “<td>Path</td><td>slot</td><td>MAC Address</td><td>lan</td><td>IP Address</td><td>vlan</td><td>Link Status</td><tr>” >> ${IDX_HTML}
writehtml Path slot MAC_Address lan IP_Address vlan Link_Status
#echo “$nparinfo”
# echo “Path slot MAC lan check ip”
# 2/0/5/1/0/6/1 4 0x002264E4948B lan1 10.8.128.162
echo “Path slot MAC Address lan ipaddress vlan linkstatus”
/usr/sbin/ioscan -fnk | awk ‘/^lan/ {print $3}’ |while read -r path
do
ip=””;
echo $path | sed ‘s/\// /g’ | read p1 p2 p3 p4 p5 p6 p7
macaddy=$(lanscan | awk ‘{if($1 == “‘${path}'”) print $2}’)
lanid=$(lanscan | awk ‘{if($1 == “‘${path}'”) print $5}’)
plan=$(lanscan | awk ‘{if($1 == “‘${path}'”) print $3}’)
lchk=$(/usr/sbin/linkloop -i $plan $macaddy 2>/dev/null | grep “OK”)
# If linkloop produces postive results then see if there is an ip address
ip=”IP not set”
if [ -n “$lchk” ]
then
# echo “lchk not null. running ifconfig command”
ip=$(/usr/sbin/ifconfig $lanid | grep netmask | awk ‘{print $2}’)
fi
# roll through the router table and see if you can establish
# linkloop with the gateway
DRMAC=”No link..”
DVLAN=”Not found”
#while [[ “$value” != “val1” || “$value” != “val2” || “$value” != “val3” ]]
while read -r DL
do
rmacaddy=$(echo $DL | awk -F: ‘{print $2}’)
rvlan=$(echo $DL | awk -F: ‘{print $3}’)
rlchk=$(/usr/sbin/linkloop -i $plan $rmacaddy 2>/dev/null | grep “OK”)
if [ -n “$rlchk” ]
then
# echo “rlchk not null. setting vlan information.”
DRMAC=${rmacaddy}
DVLAN=${rvlan}
break;
fi
done < $MA
# echo “${path} ${p7} ${macaddy} ${lanid} ${lchk} ${ip} ”
#p1=$(echo $path | awk -F/ ‘{print $1}’);
#p2=$(echo $path | awk -F/ ‘{print $2}’);
#p3=$(echo $path | awk -F/ ‘{print $3}’);
#p4=$(echo $path | awk -F/ ‘{print $4}’);
#p5=$(echo $path | awk -F/ ‘{print $5}’);
#p6=$(echo $path | awk -F/ ‘{print $6}’);
#p7=$(echo $path | awk -F/ ‘{print $7}’);
portpath=$(echo $path | awk -F/ ‘{print $3}’)
actualport=$(awk -F: ‘{if($2 == “‘${portpath}'” && $3 == “‘$mod'”) print $1}’ ${DF})
# echo “Actual path: ${p1} ${p2} ${p3} ${p4} ${p5} ${p6} ${p7} ${actualport} ${ip} ${macaddy} ${lanid} ${ip}”
echo “${path} ${actualport} ${macaddy} ${lanid} ${ip} ${DVLAN} ${DRMAC}”
# echo “<td>${path}</td><td>${actualport}</td><td>${macaddy}</td><td>${lanid}</td><td>${ip}</td><td>${DVLAN}</td><td>${DRMAC}</td><tr>” >> ${IDX_HTML}
writehtml ${path} ${actualport} ${macaddy} ${lanid} ${ip} ${DVLAN} ${DRMAC}
done
echo “Fiber Channel….”
# echo “<td>Fiber Channel….</td><tr>” >> ${IDX_HTML}
writehtml “Fiber Channel”
echo “PATH slot Device… Status spd Hardware address”
# echo “<td>PATH</td><td>slot</td><td>Device</td><td>Status</td><td>speed</td><td>Hardware address</td><tr>” >> ${IDX_HTML}
writehtml PATH slot Device Status speed Hardware address
#/usr/sbin/ioscan -fnCfc | grep fcd | awk ‘{print $3}’ |while read -r path
/usr/sbin/ioscan -fnk | awk ‘/^fc / {hw=$3;getline;print hw,$1}’ |while read -r hw devfile
do
# echo “diag ${hw} dev file … ${devfile}”
port=$(echo $hw | awk -F/ ‘{print $3}’)
OSTAT=$(fcmsutil $devfile | awk ‘/ONLINE/ {print $4}’)
LSPD=$(fcmsutil $devfile | awk ‘/Link Speed/ {print $4}’)
WWN=$(fcmsutil $devfile | awk ‘/N_Port Port World Wide Name/ {print $7}’)
# OSTAT=$(fcmsutil /dev/fcd1 | awk ‘/ONLINE/ {print $4}’)
# LSPD=$(fcmsutil /dev/fcd1 | awk ‘/Link Speed/ {print $4}’)
# WWN=$(fcmsutil /dev/fcd1 | awk ‘/N_Port Port World Wide Name/ {print $7}’)
actualport=$(awk -F: ‘{if($2 == “‘${port}'” && $3 == “‘$mod'”) print $1}’ ${DF})
echo “$hw ${actualport} $devfile ${OSTAT} ${LSPD} ${WWN}”
#echo “<td>$hw</td><td>${actualport}</td> <td>$devfile</td><td>${OSTAT}</td><td>${LSPD}</td> <td>${WWN}</td><tr>” >> ${IDX_HTML}
writehtml ${hw} ${actualport} ${devfile} ${OSTAT} ${LSPD} ${WWN}
done
#awk -F: ‘{printf(“%8s %5s %4s\n”,$1,$3,$4)}’ steve
#2/0/5/1/0/6/0
#2/0/5/1/0/6/1
cat -<< !EOF >> ${IDX_HTML}
<TR></TR></TBODY></TABLE></BODY></HTML>
!EOF
chmod a+r ${IDX_HTML}
# Added to copy the data file to my home directory for diagnosis.
cp syslayout.html /home/sprotte
chmod a+r /home/sprotte/syslayout.html
super.translate.dat
—–
root@gitop2:/root # more /usr/global/etc/super.translate.dat
11:8:SD64B
10:9:SD64B
9:10:SD64B
8:12:SD64B
7:13:SD64B
6:14:SD64B
5:6:SD64B
4:5:SD64B
3:4:SD64B
2:2:SD64B
1:1:SD64B
0:0:SD64B
1:8:rp8420
2:10:rp8420
3:12:rp8420
4:14:rp8420
5:6:rp8420
6:4:rp8420
7:2:rp8420
8:1:rp8420
more /usr/global/etc/router.macadd.dat
Format:
IP Address : MAC Address : vlan# : Description
:0x00000c07ac0a:vlan9:HP-UX Production
Obviously this data varies from place the place. The Mac address of the router is used to check network connectivity with the linkloop command
Tags: fiber channel adaptor, forums.itrc.hp.com, high capacity volume group, patches, SD-UX, superdome
20 May 10 clean up procedure after ignite replication of hpvm host
This errror is created by Ignite replication of an hpvm system. The following checks device integrity and cleans up errors created by Ignite replication.
hpvmcreate: ERROR (jdeautp1): Incorrect backing device type.
First check for errors with this script (I may check this in at some point)
#!/usr/bin/sh
#
# Unofficial quick and dirty passthru DSF check script
#
# It walks all /dev/pt/* files and tries to find corresponding /dev/rdisk
# or /dev/rtape files. If they are foudn their minor numbers are compared.
#
# @(#) pt_check.sh v1.1 – stanm@wtec
#
for i in $(ls /dev/pt/*)
do
# ll $i
shortname=${i##*_}
printf “checking $shortname”
minor1=$(ll $i|awk ‘{print $6}’)
# echo minor1=$minor ($i)
if [ -c /dev/rdisk/$shortname ]; then
minor2=$(ll /dev/rdisk/$shortname|awk ‘{print $6}’)
# echo minor2=$minor2 ($/dev/rdisk/$shortname)
if [[ “x$minor1” = “x$minor2″ ]]; then
printf ” – OK\n”
else
printf ” – Minor numbers are probably incorrect\n”
printf “minor1=$minor1 ($i) vs ”
printf “minor2=$minor2 (/dev/rdisk/$shortname)\n”
fi
else
# could be tape
if [ -c /dev/rtape/${shortname}_BEST ]; then
minor2=$(ll /dev/rtape/${shortname}_BEST|awk ‘{print $6}’)
if [[ “x$minor1” = “x$minor2″ ]]; then
printf ” – OK\n”
else
printf ” – Minor numbers are probably incorrect\n”
printf “minor1=$minor1 ($i) vs ”
printf “minor2=$minor2 (/dev/rtape/${shortname}_BEST)\n”
fi
else
printf ” – /dev/rdisk/$shortname or /dev/rtape/${shortname}_BEST not found – check skipped\n”
fi
fi
done
Output indicating problems:
checking disk11 – Minor numbers are probably incorrect
minor1=0x000005 (/dev/pt/pt_disk11) vs minor2=0x000008 (/dev/rdisk/disk11)
checking disk12 – Minor numbers are probably incorrect
minor1=0x000006 (/dev/pt/pt_disk12) vs minor2=0x000009 (/dev/rdisk/disk12)
checking disk13 – Minor numbers are probably incorrect
minor1=0x000007 (/dev/pt/pt_disk13) vs minor2=0x00000a (/dev/rdisk/disk13)
checking disk14 – Minor numbers are probably incorrect
minor1=0x000008 (/dev/pt/pt_disk14) vs minor2=0x00000b (/dev/rdisk/disk14)
checking disk15 – Minor numbers are probably incorrect
minor1=0x000009 (/dev/pt/pt_disk15) vs minor2=0x00000c (/dev/rdisk/disk15)
checking disk17 – OK
checking disk18 – /dev/rdisk/disk18 or /dev/rtape/disk18_BEST not found – check skipped
checking disk19 – Minor numbers are probably incorrect
minor1=0x000017 (/dev/pt/pt_disk19) vs minor2=0x000013 (/dev/rdisk/disk19)
checking disk2 – OK
checking disk22 – Minor numbers are probably incorrect
minor1=0x000018 (/dev/pt/pt_disk22) vs minor2=0x000014 (/dev/rdisk/disk22)
checking disk23 – Minor numbers are probably incorrect
minor1=0x000019 (/dev/pt/pt_disk23) vs minor2=0x000015 (/dev/rdisk/disk23)
checking disk3 – OK
checking disk5 – OK
checking disk8 – /dev/rdisk/disk8 or /dev/rtape/disk8_BEST not found – check skipped
checking disk9 – /dev/rdisk/disk9 or /dev/rtape/disk9_BEST not found – check skipped
Correction procedure:
cd /var/opt/hpvm/common/
rm -f hpvm_devinit
cd /dev/pt
ls
rm -f *
hpvmdevmgmt -I
Consider this a necessary procedure to clean up after ignite replication
Tags: forums.itrc.hp.com, high capacity volume group, HP-UX, hpux, hpvm, ia64, Ignite-UX, LVM
18 May 10 swlist command to provide install date
New trick learned from HP support backline engineer.
swlist -l fileset -a revision -a title -a state -a install_date
———Sample output ——
# vmGuestLib B.04.00 Integrity VM vmGuestLib 200903081306.51
vmGuestLib.GUEST-LIB B.04.00 Integrity VM GUEST-LIB fileset 200903081306.51 configured
# vmProvider B.04.00 WBEM Provider for Integrity VM vmProvider 200903081306.59
vmProvider.VM-PROV-CORE B.04.00 WBEM Provider for Integrity VM VM-PROV-CORE 200903081306.59 configured
Tags: forums.itrc.hp.com, high capacity volume group, HP-UX, hpux, Ignite-UX, patches, patching, SD-UX, SDUX
22 Feb 10 Obtain Fiber card WWN information from HP-UX npar
This was developed jointly by myself and Ted Fisher of Dana. Ted did most of the work, because I had to duck out of the office. The idea is however to take the utility fcmsutil and get it working in the recovery shell was developed jointly.
What follows is a putty log, with certain proprietary network information removed and a procedure.
Connect to the Console that controls the npar.
Welcome to the
Management Processor
HP 9000 and Integrity Superdome Server SD64B
Supported firmware-updateable entity combination: Recipe 8.7e
MP MAIN MENU:
CO: Consoles
VFP: Virtual Front Panel
CM: Command Menu
CL: Console Logs
SL: Show Logs
FW: Firmware Update
HE: Help
X: Exit Connection
[dome-m1c] MP> co
Partitions available:
# Name
— —-
0) dome-m1-NPAR0
1) dome-m1-NPAR1
2) dome-m1-NPAR2
Q) Quit
Please select partition number: 2
Connecting to OS Console: dome-m1-NPAR2
(Use <Ctrl-b> to return to main menu.)
Client MAC Address: 00 22 64 E4 74 B2
Shell> lanboot select -cip 10.91.138.167 -sip 10.91.138.162 -m 255.255.255.0 -b “/
opt/ignite/boot/Rel_B.11.31/nbp.efi”
01 Acpi(HWP0002,PNP0A03,804)/Pci(1|0)/Pci(6|0)/Mac(002264E47438)
02 Acpi(HWP0002,PNP0A03,804)/Pci(1|0)/Pci(6|1)/Mac(002264E47439)
03 Acpi(HWP0002,PNP0A03,805)/Pci(1|0)/Pci(6|0)/Mac(002264E47444)
04 Acpi(HWP0002,PNP0A03,805)/Pci(1|0)/Pci(6|1)/Mac(002264E47445)
05 Acpi(HWP0002,PNP0A03,806)/Pci(1|0)/Pci(6|0)/Mac(002264E474A4)
06 Acpi(HWP0002,PNP0A03,806)/Pci(1|0)/Pci(6|1)/Mac(002264E474A5)
07 Acpi(HWP0002,PNP0A03,80C)/Pci(1|0)/Pci(6|0)/Mac(002264E474DE)
08 Acpi(HWP0002,PNP0A03,80C)/Pci(1|0)/Pci(6|1)/Mac(002264E474DF)
09 Acpi(HWP0002,PNP0A03,80D)/Pci(1|0)/Pci(6|0)/Mac(002264E474B2)
10 Acpi(HWP0002,PNP0A03,80D)/Pci(1|0)/Pci(6|1)/Mac(002264E474B3)
11 Acpi(HWP0002,PNP0A03,80E)/Pci(1|0)/Pci(6|0)/Mac(002264E4745C)
12 Acpi(HWP0002,PNP0A03,80E)/Pci(1|0)/Pci(6|1)/Mac(002264E4745D)
Select Desired LAN: 10
Client MAC Address: 00 22 64 E4 74 B3
LAN Configuration:
Client MAC Address : 00 22 64 E4 74 B3
Client IP Address : 10.91.138.167
Subnet Mask : 255.255.255.0
Boot Server IP Address : 10.91.138.162
DHCP Server IP Address : 0.0.0.0
Retrieving File Size.
Boot file name: /opt/ignite/boot/nbp.efi
Boot file size: 24576 bytes
Retrieving File (TFTP).
Executing Image: “/opt/ignite/boot/nbp.efi”
Optional Data: NONE
@(#) HP-UX IA64 Network Bootstrap Program Revision 1.0
Downloading HPUX bootloader
Starting HPUX bootloader
Obtaining size of fpswa.efi / (328192 bytes)
Downloading file fpswa.efi -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\ (328192 bytes)
(C) Copyright 1999-2008 Hewlett-Packard Development Company, L.P.
All rights reserved
HP-UX Boot Loader for IPF — Revision 2.036
Booting from Lan
Obtaining size of AUTO | (226 bytes)
Downloading file AUTO /- (226 bytes)
Obtaining size of AUTO \ (226 bytes)
Downloading file AUTO |/ (226 bytes)
Obtaining size of AUTO – (226 bytes)
Downloading file AUTO \| (226 bytes)
1. target OS is B.11.23 IA
2. target OS is B.11.31 IA
3. Exit Boot Loader
Choose an operating system to install that your hardware supports:2
Obtaining size of AUTO / (226 bytes)
Downloading file AUTO -\ (226 bytes)
Obtaining size of Rel_B.11.31/IINSTALL | (50966795 bytes)
Downloading file Rel_B.11.31/IINSTALL /-\ (50966795 bytes)
> System Memory = 98106 MB
loading section 0
………………………………………………………………………………………. (complete)
loading section 1
…………….. (complete)
loading symbol table
Obtaining size of Rel_B.11.31/IINSTALLFS | (61341696 bytes)
Downloading file Rel_B.11.31/IINSTALLFS /-\|//-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/- (61341696 bytes)
loading ram disk file (Rel_B.11.31/IINSTALLFS).
………………………………………………………………………………………………………
(complete)
Launching Rel_B.11.31/IINSTALL
SIZE: Text:50828K + Data:8272K + BSS:23776K = Total:82878K
Console is on Serial Device – via PCDP
Booting kernel…
krs_read_mfs: Error 5 opening MFS.
Loaded ACPI revision 2.0 tables.
krs_read_mfs: Error 5 opening MFS.
Memory Class Setup
————————————————————————-
Class Physmem Lockmem Swapmem
————————————————————————-
System : 93316 MB 93316 MB 93316 MB
Kernel : 93316 MB 93316 MB 93316 MB
User : 90509 MB 80238 MB 80553 MB
————————————————————————-
ktracer is off until requested.
Installing Socket Protocol families AF_INET and AF_INET6
Kernel EVM initialized
sec_init(): kernel RPC authentication/security initialization.
secgss_init(): kernel RPCSEC_GSS security initialization.
rpc_init(): kernel RPC initialization.
rpcmod_install(): kernel RPC STREAMS module “rpcmod” installation. …(driver_install)
NOTICE: nfs_client_pv3_install(): nfs3 File system was registered at index 11.
NOTICE: nfs_client_pv4_install(): nfs4 File system was registered at index 12.
iether0: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/4/1/0/6/0
iether1: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/4/1/0/6/1
iether2: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/5/1/0/6/0
iether3: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/5/1/0/6/1
iether4: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/6/1/0/6/0
iether5: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/6/1/0/6/1
iether6: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/12/1/0/6/0
iether7: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/12/1/0/6/1
iether8: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/13/1/0/6/0
iether9: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/13/1/0/6/1
iether10: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/14/1/0/6/0
iether11: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 8/0/14/1/0/6/1
System Console is on the Built-In Serial Interface
iether12: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/4/1/0/6/0
iether13: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/4/1/0/6/1
iether14: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/5/1/0/6/0
iether15: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/5/1/0/6/1
iether16: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/6/1/0/6/0
iether17: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/6/1/0/6/1
iether18: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/12/1/0/6/0
iether19: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/12/1/0/6/1
iether20: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/13/1/0/6/0
iether21: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/13/1/0/6/1
iether22: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/14/1/0/6/0
iether23: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 10/0/14/1/0/6/1
AF_INET socket/streams output daemon running, pid 158
afinet_prelink: module installed
Starting the STREAMS daemons-phase 1
Swap device table: (start & size given in 512-byte blocks)
entry 0 – auto-configured on root device; ignored – no room
WARNING: No swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: B.11.31_LR FLAVOR=perf nfsauth: lookupname: 2
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 100461436 Kbytes, lockable: 80228428 Kbytes, available: 90518748 Kbytes
* Preparing to execute init…
======= 02/19/10 13:42:01 EST HP-UX Installation Initialization. (Fri Feb 19
13:42:01 EST 2010)
@(#)Ignite-UX Revision C.7.7.93
@(#)ignite/launch (opt) Revision:
/branches/IUX_RA0809/ignite/src@74753 Last Modified: 2008-07-11
12:27:58 -0600 (Fri, 11 Jul 2008)
* Configuring RAM filesystems…
* Scanning system for IO devices…
* Boot device is: 8/0/13/1/0/6/1
NOTE: There were no disk devices found during the scan. Make sure that the
destination disks are connected and powered on. You may choose to
scan for more disk drives from next menu on the console.
NOTE: Empty primary boot path reported by setboot: Primary bootpath :
NOTE: Primary path not currently set to an existing disk device.
* Setting keyboard language.
.i
i
### We poke around and try and get the hardware information and the World Wide Name.
Welcome to Ignite-UX!Use the <tab> key to navigate between fields, and the arrow keys
within fields. Use the <return/enter> key to select an item.
Use the <return/enter> or <space-bar> to pop-up a choices list. If the
menus are not clear, select the “Help” item for more information.Hardware Summary:System Model: ia64 hp superdome server SD64B
+———————-+—————+——————–+[ Scan Again ]
| Disks: 0 ( 0.0GB)| Floppies: 0 | LAN cards: 24 |
| CD/DVDs:0 | Tapes: 0 | Memory: 98106Mb |
| Graphics Ports: 0 | IO Buses: 24 | CPUs:24 |[ H/W Details ]
+———————-+—————+——————–+[ Install HP-UX ][ Run an Expert Recovery Shell ][ Advanced Options][ Reboot ][ Help ] Install HP-UX Run an Expert Recovery Shell Networking must be enabled in order to load a shell.
(Press any key to continue.)LAN Interface SelectionMore than one network interface was detected on the system. Youwill need to select the interface to enable. Only one interfacecan be enabled, and it must be the one connected to the networkthat can be used in contacting the install and/or SD servers.Use the <tab> and/or arrow keys to move to the desired LAN deviceto enable, then press <Return>.HW Path Interface Station Address Description———————————————————-[ 8/0/4/1/0/6 lan0 0x002264E47438 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/4/1/0/6 lan1 0x002264E47439 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/5/1/0/6 lan2 0x002264E47444 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/5/1/0/6 lan3 0x002264E47445 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/6/1/0/6 lan4 0x002264E474A4 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/6/1/0/6 lan5 0x002264E474A5 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/12/1/0/ lan6 0x002264E474DE HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/12/1/0/ lan7 0x002264E474DF HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/13/1/0/ lan8 0x002264E474B2 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/13/1/0/ lan9 0x002264E474B3 HP_AD194-60001_PCI/PCI-X_1000B ][ 8/0/14/1/0/ lan10 0x002264E4745C HP_AD194-60001_PCI/PCI-X_1000B ]8/0/13/1/0/ lan9 0x002264E474B3 HP_AD194-60001_PCI/PCI-X_1000B* Searching the network for a DHCP server to supply default networkinginformation….This could take up to 30 seconds if a DHCP server cannot be found. Ifyou wish to cancel the DHCP server search, you may press CTRL-C now.* Could not get DHCP information. No host specific network defaultswill be supplied. (dhcpclient returned: 9)NETWORK CONFIGURATIONNETWORK CONFIGURATIONThis system’s hostname: Internet protocol address (eg. 15.2.56.1) of this host: Default gateway routing internet protocol address: 10.8.128.1 The subnet mask (eg. 255.255.248.0 or 0xfffff800): 255.255.252.0 IP address of the Ignite-UX server system: 10.8.128.162 Is this networking information only temporary? [ No ][ OK ][ Cancel ][ Help ]10.8.128.167o No OK OK ancelancelHelp Help test <est NETWORK CONFIGURATIONThis system’s hostname:<est Internet protocol address (eg. 15.2.56.1) of this host: Default gateway routing internet protocol address: 10.8.128.1 The subnet mask (eg. 255.255.248.0 or 0xfffff800): 255.255.252.0 IP address of the Ignite-UX server system: 10.8.128.162 Is this networking information only temporary? [ No ][ OK ][ Cancel ][ Help ]10.8.128.167o No OK OK ancelancelHelp Help testo YesYesYes OK OK * Bringing up Network (lan9)
add net default: gateway 10.8.128.1
* Reading configuration information from server…
* Creating disk device files…
* Loading the recovery commands…
### We arrive at the recovery shell.
HP-UX NETWORK SYSTEM RECOVERY
WARNING: YOU ARE SUPERUSER !!
Checking for required components on the Ignite Server……..
Loading some basic commands…
Required files exist … Proceeding
Cannot find the disk referenced by the primary
boot path: “” in /tmp/hw.info or /tmp/io.info.
The default chosen for the root disk may not be correct.
press <return> to continue
HP-UX NETWORK SYSTEM RECOVERY
MAIN MENU
s. Search for a file
b. Reboot
l. Load a file
r. Recover an unbootable HP-UX system
x. Exit to shell
This menu is for listing and loading the tools contained on the core media.
Once a tool is loaded, it may be run from the shell. Some tools require other
files to be present in order to successfully execute.
Select one of the above: Dead gateway detection can’t ping the last remaining default gateway at 0xa088001 .See ndd -h ip_ire_gw_probe for more info
Dead gateway detection can’t ping the last remaining default gateway at 0xa088001 .See ndd -h ip_ire_gw_probe for more info
l NOTE: Loading some files may require other files/libraries to be loaded.
If an attempt is made to load a file, and an error message is
encountered when the command is invoked, it may be useful to use
the chatr command (on a system that is up and running) to ensure that
dependencies are met. See chatr(1) for more details.
For some commands (vi, ftp, rcp), the dependent files will be
automatically loaded. For others, you need to load them manually.
If you specify a filename of “all” a list of all the files available
will be displayed.
## The recovery shell put the OS into ram based file systems.
Filesystem kbytes used avail %cap iused ifree iused Mounted on
/ 57892 23319 34573 40% 68 14332 0% ?
Filesystem kbytes used avail %cap iused ifree iused Mounted on
/RAMFS1 102400 17835 79393 18% 93 21139 0% ?
Filesystem kbytes used avail %cap iused ifree iused Mounted on
/RAMFS2 1572864 24791 1451423 2% 127 387017 0% ?
## We need tar, so we need to transfer tar to the recovery shell.
Enter the filename(s) to load:
/usr/bin/tar
******** THE REQUESTED FILE(S): ***********
./usr/bin/tar
Is the above load list correct? [y/(n)] y
********* downloading the files *******
x ./usr/bin/tar, 146032 bytes, 286 tape blocks
<Press return to continue>
HP-UX NETWORK SYSTEM RECOVERY
MAIN MENU
s. Search for a file
b. Reboot
l. Load a file
r. Recover an unbootable HP-UX system
x. Exit to shell
This menu is for listing and loading the tools contained on the core media.
Once a tool is loaded, it may be run from the shell. Some tools require other
files to be present in order to successfully execute.
Select one of the above: l
NOTE: Loading some files may require other files/libraries to be loaded.
If an attempt is made to load a file, and an error message is
encountered when the command is invoked, it may be useful to use
the chatr command (on a system that is up and running) to ensure that
dependencies are met. See chatr(1) for more details.
For some commands (vi, ftp, rcp), the dependent files will be
automatically loaded. For others, you need to load them manually.
If you specify a filename of “all” a list of all the files available
will be displayed.
At this point we have on the Ignite server craeted a file called fcms.tar. We have to use tftp to get the file into the Ignite server.
cd /opt/fcms
tar -cvf /var/opt/ignite/fcms.tar .
cd /usr/lib/hpux64
tar -cvf /var/opt/ignite/lib64.tar .
tftp <ip of ignite server>
tftp> get /var/opt/ignite/fcms.tar
Received 3689985 bytes in 0.7 seconds
tftp> Dead gateway detection can’t ping the last remaining default gateway at 0xa088001 .See ndd -h ip_ire_gw_probe for more info
tftp> quit
# ll
total 385884
-rw-r–r– 1 root sys 3665920 Feb 19 14:00 fcms.tar
-rw-r–r– 1 root sys 192040960 Feb 19 13:58 lib64.tar
# pwd
/usr/lib/hpux64
# tar mv fcms.tar /opt/fcms
# ll
total 375096
-rw-r–r– 1 root sys 192040960 Feb 19 13:58 lib64.tar
# tar -xvf lib64.tar
x ./libntl.so symbolic link to ./libntl.so.1
x ./libntl.so.1, 91352 bytes, 179 tape blocks
x ./netmgr/libnetmgr.so symbolic link to ./libnetmgr.so.1
x ./netmgr/libnetmgr.so.1, 328256 bytes, 642 tape blocks
x ./netmgr/libncweb_vlan.so symbolic link to ./libnetmgr_vlan.so.1
x ./netmgr/libnetmgr_dlpi.so symbolic link to ./libnetmgr_dlpi.so.1
x ./netmgr/libnetmgr_dlpi.so.1, 84704 bytes, 166 tape blocks
x ./netmgr/libnetmgr_vlan.so symbolic link to ./libnetmgr_vlan.so.1
x ./netmgr/libnetmgr_vlan.so.1, 359816 bytes, 703 tape blocks
x ./netmgr/libncweb_btlan.so symbolic link to ./libncweb_btlan.so.1
x ./netmgr/libncweb_btlan.so.1, 192872 bytes, 377 tape blocks
x ./netmgr/libnetmgr_btlan.so symbolic link to ./libncweb_btlan.so.1
x ./netmgr/libncweb_igssn.so symbolic link to /usr/lib/hpux64/netmgr/libncweb_igssn.so.1
x ./netmgr/libncweb_igssn.so.1, 350936 bytes, 686 tape blocks
x ./netmgr/libnetmgr_igssn.so symbolic link to /usr/lib/hpux64/netmgr/libncweb_igssn.so.1
x ./netmgr/libncweb_gelan.so symbolic link to ./libncweb_gelan.so.1
x ./netmgr/libncweb_gelan.so.1, 351216 bytes, 686 tape blocks
x ./netmgr/libnetmgr_gelan.so symbolic link to ./libncweb_gelan.so.1
x ./netmgr/libncweb_iether.so symbolic link to ./libncweb_iether.so.1
x ./netmgr/libncweb_iether.so.1, 358384 bytes, 700 tape blocks
x ./netmgr/libnetmgr_iether.so symbolic link to ./libncweb_iether.so.1
x ./netmgr/libncweb_igelan.so symbolic link to ./libncweb_igelan.so.1
x ./netmgr/libncweb_igelan.so.1, 354144 bytes, 692 tape blocks
x ./netmgr/libnetmgr_igelan.so symbolic link to ./libncweb_igelan.so.1
x ./netmgr/libncweb_intl100.so symbolic link to ./libncweb_intl100.so.1
x ./netmgr/libncweb_intl100.so.1, 187584 bytes, 367 tape blocks
x ./netmgr/libnetmgr_intl100.so symbolic link to ./libncweb_intl100.so.1
x ./netmgr/libncweb_apa.so symbolic link to ./libnetmgr_apa.so.1
x ./netmgr/libnetmgr_apa.so symbolic link to ./libnetmgr_apa.so.1
x ./netmgr/libnetmgr_apa.so.1, 881408 bytes, 1722 tape blocks
x ./netmgr/libnetmgr_hp_apa.so symbolic link to ./libnetmgr_apa.so.1
x ./libipv6.so symbolic link to ./libipv6.so.1
x ./libipv6.so.1, 76768 bytes, 150 tape blocks
x ./libnm.so symbolic link to ./libnm.so.1
x ./libnm.so.1, 244296 bytes, 478 tape blocks
x ./libxnet.so symbolic link to ./libxnet.so.1
x ./libxnet.so.1, 96464 bytes, 189 tape blocks
x ./libxti.so symbolic link to ./libxti.so.1
x ./libxti.so.1, 298840 bytes, 584 tape blocks
x ./cra/libmscra.so symbolic link to ./libmscra.so.1
x ./cra/libmscra.so.1, 361264 bytes, 706 tape blocks
x ./cra/liblancra.so symbolic link to ./liblancra.so.1
x ./cra/liblancra.so.1, 162048 bytes, 317 tape blocks
x ./cra/libhssn_cra.so symbolic link to /usr/lib/hpux64/cra/libhssn_cra.so.1
x ./cra/libhssn_cra.so.1, 100528 bytes, 197 tape blocks
x ./libIO.so symbolic link to ./libIO.so.1
x ./libIO.so.1, 292384 bytes, 572 tape blocks
x ./libcra.so symbolic link to ./libcra.so.1
x ./libcra.so.1, 196200 bytes, 384 tape blocks
x ./libcres.a, 94982 bytes, 186 tape blocks
x ./libhg.so symbolic link to ./libhg.so.1
x ./libhg.so.1, 76664 bytes, 150 tape blocks
x ./libmxndbg.so symbolic link to ./libmxndbg.so.1
x ./libmxndbg.so.1, 82816 bytes, 162 tape blocks
x ./libolrad.so symbolic link to ./libolrad.so.1
x ./libolrad.so.1, 91656 bytes, 180 tape blocks
x ./libprocsm.so symbolic link to ./libprocsm.so.1
x ./libprocsm.so.1, 74416 bytes, 146 tape blocks
x ./libsec.so symbolic link to ./libsec.so.1
x ./libsec.so.1, 582760 bytes, 1139 tape blocks
x ./libuca.so symbolic link to ./libuca.so.1
x ./libuca.so.1, 85680 bytes, 168 tape blocks
x ./libunalign.so symbolic link to ./libunalign.so.1
x ./libunalign.so.1, 84248 bytes, 165 tape blocks
x ./libvparusr.so symbolic link to ./libvparusr.so.1
x ./libvparusr.so.1, 176000 bytes, 344 tape blocks
x ./milli.a, 52590 bytes, 103 tape blocks
x ./millikern.a, 60144 bytes, 118 tape blocks
x ./libnsl.so symbolic link to ./libnsl.so.1
x ./librpcsec_gss.sl symbolic link to ./librpcsec_gss.so.1
x ./libacps.so symbolic link to ./libacps.so.1
x ./libacps.so.1, 82480 bytes, 162 tape blocks
x ./librbac.so symbolic link to ./librbac.so.1
x ./librbac.so.1, 278936 bytes, 545 tape blocks
x ./libldap.so symbolic link to /opt/ldapux/lib/hpux64/libldap.so.1
x ./libp/libc.so symbolic link to ./libc.so.1
x ./libp/libc.so.1, 5267664 bytes, 10289 tape blocks
x ./libp/libcres.a, 102214 bytes, 200 tape blocks
x ./libp/libdlv_vxfs.so symbolic link to ./libdlv_vxfs.so.1
x ./libp/libdlv_vxfs.so.1, 71664 bytes, 140 tape blocks
x ./unix2003.o, 1848 bytes, 4 tape blocks
x ./unix95.o, 1848 bytes, 4 tape blocks
x ./unix98.o, 1848 bytes, 4 tape blocks
x ./aries64.so, 5164024 bytes, 10086 tape blocks
x ./dld.so, 1091952 bytes, 2133 tape blocks
x ./dpd/libjvm.so.bpd, 12672 bytes, 25 tape blocks
x ./libCsup.so symbolic link to ./libCsup.so.1
x ./libCsup.so.1, 677016 bytes, 1323 tape blocks
x ./libc.so symbolic link to ./libc.so.1
x ./libc.so.1, 4898520 bytes, 9568 tape blocks
x ./libcext.so symbolic link to ./libcext.so.1
x ./libcext.so.1, 70384 bytes, 138 tape blocks
x ./libcl.so symbolic link to ./libcl.so.1
x ./libcl.so.1, 69336 bytes, 136 tape blocks
x ./libcurses.so symbolic link to ./libxcurses.so.1
x ./libdl.so symbolic link to ./libdl.so.1
x ./libdl.so.1, 78488 bytes, 154 tape blocks
x ./libdld.so symbolic link to ./libdl.so.1
x ./libelf.so symbolic link to ./libelf.so.1
x ./libelf.so.1, 336656 bytes, 658 tape blocks
x ./libgen.so symbolic link to ./libgen.so.1
x ./libgen.so.1, 81904 bytes, 160 tape blocks
x ./libgprof.so symbolic link to ./libgprof.so.1
x ./libgprof.so.1, 90696 bytes, 178 tape blocks
x ./libl.so symbolic link to ./libl.so.1
x ./libl.so.1, 82720 bytes, 162 tape blocks
x ./libl_thread.so symbolic link to ./libl_thread.so.1
x ./libl_thread.so.1, 83864 bytes, 164 tape blocks
x ./libm.so symbolic link to ./libm.so.1
x ./libm.so.1, 6465904 bytes, 12629 tape blocks
x ./libnss_files.so.1, 179704 bytes, 351 tape blocks
x ./libpam.so symbolic link to ./libpam.so.1
x ./libpam.so.1, 91528 bytes, 179 tape blocks
x ./libprof.so symbolic link to ./libprof.so.1
x ./libprof.so.1, 79688 bytes, 156 tape blocks
x ./libpsm.so symbolic link to ./libpsm.so.1
x ./libpsm.so.1, 73584 bytes, 144 tape blocks
x ./libpthread.so symbolic link to ./libpthread.so.1
x ./libpthread.so.1, 1535512 bytes, 3000 tape blocks
x ./libpthread_tr.so symbolic link to ./libpthread_tr.so.1
x ./libpthread_tr.so.1, 1780504 bytes, 3478 tape blocks
x ./librt.so symbolic link to ./librt.so.1
x ./librt.so.1, 85568 bytes, 168 tape blocks
x ./librwtool.so symbolic link to ./librwtool.so.1
x ./librwtool.so.1, 3684800 bytes, 7197 tape blocks
x ./librwtool_v2.so symbolic link to ./librwtool_v2.so.1
x ./librwtool_v2.so.1, 3858512 bytes, 7537 tape blocks
x ./libsin.so symbolic link to ./libsin.so.1
x ./libsin.so.1, 77032 bytes, 151 tape blocks
x ./libstd.so symbolic link to ./libstd.so.1
x ./libstd.so.1, 538840 bytes, 1053 tape blocks
x ./libstd_v2.so symbolic link to ./libstd_v2.so.1
x ./libstd_v2.so.1, 3297648 bytes, 6441 tape blocks
x ./libstream.so symbolic link to ./libstream.so.1
x ./libstream.so.1, 660248 bytes, 1290 tape blocks
x ./libunwind.so symbolic link to ./libunwind.so.1
x ./libunwind.so.1, 635200 bytes, 1241 tape blocks
x ./libuseracct.so symbolic link to ./libuseracct.so.1
x ./libuseracct.so.1, 77800 bytes, 152 tape blocks
x ./libxcurses.so.1, 1383776 bytes, 2703 tape blocks
x ./liby.so symbolic link to ./liby.so.1
x ./liby.so.1, 73648 bytes, 144 tape blocks
x ./pa_boot64.so, 160704 bytes, 314 tape blocks
x ./uld.so, 182864 bytes, 358 tape blocks
x ./libcrypto.a symbolic link to /opt/openssl/lib/hpux64/libcrypto.a
x ./libcrypto.so symbolic link to /opt/openssl/lib/hpux64/libcrypto.so
x ./libcrypto.so.0 symbolic link to /opt/openssl/lib/hpux64/libcrypto.so.0
x ./libcrypto.so.1 symbolic link to /opt/openssl/lib/hpux64/libcrypto.so.1
x ./libssl.a symbolic link to /opt/openssl/lib/hpux64/libssl.a
x ./libssl.so symbolic link to /opt/openssl/lib/hpux64/libssl.so
x ./libssl.so.0 symbolic link to /opt/openssl/lib/hpux64/libssl.so.0
x ./libssl.so.1 symbolic link to /opt/openssl/lib/hpux64/libssl.so.1
x ./engines/lib4758cca.so symbolic link to /opt/openssl/lib/hpux64/engines/lib4758cca.so
x ./engines/libaep.so symbolic link to /opt/openssl/lib/hpux64/engines/libaep.so
x ./engines/libatalla.so symbolic link to /opt/openssl/lib/hpux64/engines/libatalla.so
x ./engines/libchil.so symbolic link to /opt/openssl/lib/hpux64/engines/libchil.so
x ./engines/libcswift.so symbolic link to /opt/openssl/lib/hpux64/engines/libcswift.so
x ./engines/libgmp.so symbolic link to /opt/openssl/lib/hpux64/engines/libgmp.so
x ./engines/libnuron.so symbolic link to /opt/openssl/lib/hpux64/engines/libnuron.so
x ./engines/libsureware.so symbolic link to /opt/openssl/lib/hpux64/engines/libsureware.so
x ./engines/libubsec.so symbolic link to /opt/openssl/lib/hpux64/engines/libubsec.so
x ./liblvml.so symbolic link to /opt/lvm/lib/hpux64/liblvml.so.1
x ./libCsup.a, 1450254 bytes, 2833 tape blocks
x ./libdas.a, 520758 bytes, 1018 tape blocks
x ./liblinkmap.a, 101594 bytes, 199 tape blocks
x ./libm.a, 8314252 bytes, 16239 tape blocks
x ./librwtool.a, 6788814 bytes, 13260 tape blocks
x ./librwtool_v2.a, 7375734 bytes, 14406 tape blocks
x ./libstd.a, 746764 bytes, 1459 tape blocks
x ./libstd_v2.a, 6554730 bytes, 12803 tape blocks
x ./libstream.a, 1103494 bytes, 2156 tape blocks
x ./X11R6/libICE.so.1, 364976 bytes, 713 tape blocks
x ./X11R6/libSM.so.1, 169360 bytes, 331 tape blocks
x ./X11R6/libX11.so.1, 4119128 bytes, 8046 tape blocks
x ./X11R6/libXIE.so.1, 269088 bytes, 526 tape blocks
x ./X11R6/libXext.so.1, 357400 bytes, 699 tape blocks
x ./X11R6/libXhp11.so.1, 221336 bytes, 433 tape blocks
x ./X11R6/libXi.so.1, 209912 bytes, 410 tape blocks
x ./X11R6/libXp.so.1, 129632 bytes, 254 tape blocks
x ./X11R6/libXt.so.1, 1396744 bytes, 2729 tape blocks
x ./X11R6/libXtst.so.1, 90520 bytes, 177 tape blocks
x ./X11R6/libICE.so symbolic link to /usr/lib/hpux64/X11R6/libICE.so.1
x ./X11R6/libSM.so symbolic link to /usr/lib/hpux64/X11R6/libSM.so.1
x ./X11R6/libX11.so symbolic link to /usr/lib/hpux64/X11R6/libX11.so.1
x ./X11R6/libXIE.so symbolic link to /usr/lib/hpux64/X11R6/libXIE.so.1
x ./X11R6/libXext.so symbolic link to /usr/lib/hpux64/X11R6/libXext.so.1
x ./X11R6/libXhp11.so symbolic link to /usr/lib/hpux64/X11R6/libXhp11.so.1
x ./X11R6/libXi.so symbolic link to /usr/lib/hpux64/X11R6/libXi.so.1
x ./X11R6/libXp.so symbolic link to /usr/lib/hpux64/X11R6/libXp.so.1
x ./X11R6/libXt.so symbolic link to /usr/lib/hpux64/X11R6/libXt.so.1
x ./X11R6/libXtst.so symbolic link to /usr/lib/hpux64/X11R6/libXtst.so.1
x ./libICE.so.1 symbolic link to ./X11R6/libICE.so.1
x ./libSM.so.1 symbolic link to ./X11R6/libSM.so.1
x ./libX11.so.1 symbolic link to ./X11R6/libX11.so.1
x ./libXIE.so.1 symbolic link to ./X11R6/libXIE.so.1
x ./libXaw.so.1 symbolic link to ../../contrib/X11R6/lib/hpux64/libXaw.so.1
x ./libXext.so.1 symbolic link to ./X11R6/libXext.so.1
x ./libXhp11.so.1 symbolic link to ./X11R6/libXhp11.so.1
x ./libXi.so.1 symbolic link to ./X11R6/libXi.so.1
x ./libXmu.so.1 symbolic link to ../../contrib/X11R6/lib/hpux64/libXmu.so.1
x ./libXp.so.1 symbolic link to ./X11R6/libXp.so.1
x ./libXt.so.1 symbolic link to ./X11R6/libXt.so.1
x ./libXtst.so.1 symbolic link to ./X11R6/libXtst.so.1
x ./libIOmt.so symbolic link to ./libIOmt.so.1
x ./libIOmt.so.1, 365296 bytes, 714 tape blocks
x ./libicod.so, 11300984 bytes, 22073 tape blocks
x ./libnsl.so.1, 1510856 bytes, 2951 tape blocks
x ./libnss_compat.so.1, 89536 bytes, 175 tape blocks
x ./libnss_dns.so.1, 91184 bytes, 179 tape blocks
x ./libnss_nis.so.1, 107248 bytes, 210 tape blocks
x ./librpcsec_gss.so.1, 99792 bytes, 195 tape blocks
x ./librpcsvc.so symbolic link to ./librpcsvc.so.1
x ./librpcsvc.so.1, 109208 bytes, 214 tape blocks
x ./libstraddr.so.1, 76384 bytes, 150 tape blocks
x ./libdcekt.so symbolic link to ./libdcekt.so.1
x ./libdcekt.so.1, 13180696 bytes, 25744 tape blocks
x ./libldap_send.so.1, 243104 bytes, 475 tape blocks
x ./libnss_ldap.so.1, 1971648 bytes, 3851 tape blocks
x ./libldap_send.so symbolic link to /usr/lib/hpux64/libldap_send.so.1
x ./gss/libgssapi_krb5.so symbolic link to ./libgssapi_krb5.so.1
x ./gss/libgssapi_krb5.so.1 symbolic link to /opt/krb5core/lib/hpux64/gss/libgssapi_krb5.so.1
x ./libcom_err.so symbolic link to ./libcom_err.so.1
x ./libcom_err.so.1 symbolic link to /opt/krb5core/lib/hpux64/libcom_err.so.1
x ./libgssapi_krb5.so symbolic link to ./gss/libgssapi_krb5.so
x ./libk5crypto.so symbolic link to ./libk5crypto.so.1
x ./libk5crypto.so.1 symbolic link to /opt/krb5core/lib/hpux64/libk5crypto.so.1
x ./libkrb5.so symbolic link to ./libkrb5.so.1
x ./libkrb5.so.1 symbolic link to /opt/krb5core/lib/hpux64/libkrb5.so.1
x ./libevm.so symbolic link to ./libevm.so.1
x ./libevm.so.1, 485840 bytes, 949 tape blocks
x ./libHBAAPI.so symbolic link to /opt/snia/lib/hpux64/libHBAAPI.so
x ./libhbaapifcd.so symbolic link to /opt/fcms/lib/hpux64/libhbaapifcd.so
x ./libhbaapifclp.so symbolic link to /opt/fcms/lib/hpux64/libhbaapifclp.so
x ./libhbaapihp.so symbolic link to /opt/fcms/lib/hpux64/libhbaapihp.so
x ./libdlv_vxfs.so symbolic link to ./libdlv_vxfs.so.1
x ./libdlv_vxfs.so.1, 71664 bytes, 140 tape blocks
x ./libsascommon.so symbolic link to /opt/sas/lib/libsascommon.so.1
x ./Motif2.1/libMrm.so.1, 486976 bytes, 952 tape blocks
x ./Motif2.1/libXm.so.1, 7007912 bytes, 13688 tape blocks
x ./Motif2.1/libMrm.so symbolic link to /usr/lib/hpux64/Motif2.1/libMrm.so.1
x ./Motif2.1/libXm.so symbolic link to /usr/lib/hpux64/Motif2.1/libXm.so.1
x ./libMrm.so.1 symbolic link to ./Motif2.1/libMrm.so.1
x ./libXm.so.1 symbolic link to ./Motif2.1/libXm.so.1
x ./libcps.a, 516320 bytes, 1009 tape blocks
x ./libcps.so symbolic link to ./libcps.so.1
x ./libcps.so.1, 304720 bytes, 596 tape blocks
x ./libF90.a, 13875552 bytes, 27101 tape blocks
x ./libF90_parallel.a, 15463940 bytes, 30204 tape blocks
x ./libF90.so symbolic link to ./libF90.so.1
x ./libF90.so.1, 10920688 bytes, 21330 tape blocks
x ./libF90_parallel.so symbolic link to ./libF90_parallel.so.1
x ./libF90_parallel.so.1, 12172192 bytes, 23774 tape blocks
x ./libIO77.a, 4147142 bytes, 8100 tape blocks
x ./libIO77.so symbolic link to ./libIO77.so.1
x ./libIO77.so.1, 2912872 bytes, 5690 tape blocks
x ./libomp.a, 129772 bytes, 254 tape blocks
x ./libomp.so symbolic link to ./libomp.so.1
x ./libomp.so.1, 96792 bytes, 190 tape blocks
x ./libU77.a, 573864 bytes, 1121 tape blocks
x ./libgss.so, 296392 bytes, 579 tape blocks
x ./libnss_dce.so.1, 84328 bytes, 165 tape blocks
x ./libJudy.a, 1284862 bytes, 2510 tape blocks
x ./libJudy.so, 973024 bytes, 1901 tape blocks
x ./libbind9stub.so symbolic link to /usr/lib/hpux64/libbind9stub.so.1
x ./libbind9stub.so.1, 91256 bytes, 179 tape blocks
x ./libsys.so symbolic link to ./libsys.so.1
x ./libsys.so.1, 70560 bytes, 138 tape blocks
x ./libMrm.so symbolic link to /usr/lib/hpux64/libMrm.so.1
x ./libXm.so symbolic link to /usr/lib/hpux64/libXm.so.1
x ./libICE.so symbolic link to /usr/lib/hpux64/libICE.so.1
x ./libSM.so symbolic link to /usr/lib/hpux64/libSM.so.1
x ./libX11.so symbolic link to /usr/lib/hpux64/libX11.so.1
x ./libXIE.so symbolic link to /usr/lib/hpux64/libXIE.so.1
x ./libXext.so symbolic link to /usr/lib/hpux64/libXext.so.1
x ./libXhp11.so symbolic link to /usr/lib/hpux64/libXhp11.so.1
x ./libXi.so symbolic link to /usr/lib/hpux64/libXi.so.1
x ./libXp.so symbolic link to /usr/lib/hpux64/libXp.so.1
x ./libXt.so symbolic link to /usr/lib/hpux64/libXt.so.1
x ./libXtst.so symbolic link to /usr/lib/hpux64/libXtst.so.1
x ./libXaw.so symbolic link to /usr/lib/hpux64/libXaw.so.1
x ./libXmu.so symbolic link to /usr/lib/hpux64/libXmu.so.1
x ./libhppac.so symbolic link to ./libhppac.so.1
x ./libhppac.so.1, 159952 bytes, 313 tape blocks
# rm lib64.tar
# cd /opt/fcms
# Dead gateway detection can’t ping the last remaining default gateway at 0xa088001 .See ndd -h ip_ire_gw_probe for more info
ll
total 7160
-rw-r–r– 1 root sys 3665920 Feb 19 14:00 fcms.tar
# tar -xvf fcms.tar
x ./include/snia_common.h, 16584 bytes, 33 tape blocks
x ./lib/hpux32/libhbaapifcd.so symbolic link to ./libhbaapifcd.so.1
x ./lib/hpux32/libhbaapifcd.so.1, 267904 bytes, 524 tape blocks
x ./lib/hpux32/libhbaapifclp.so symbolic link to ./libhbaapifclp.so.1
x ./lib/hpux32/libhbaapifclp.so.1, 294104 bytes, 575 tape blocks
x ./lib/hpux32/libhbaapihp.so symbolic link to ./libhbaapihp.so.1
x ./lib/hpux32/libhbaapihp.so.1, 263560 bytes, 515 tape blocks
x ./lib/hpux64/libhbaapifcd.so symbolic link to ./libhbaapifcd.so.1
x ./lib/hpux64/libhbaapifcd.so.1, 274096 bytes, 536 tape blocks
x ./lib/hpux64/libhbaapifclp.so symbolic link to ./libhbaapifclp.so.1
x ./lib/hpux64/libhbaapifclp.so.1, 300416 bytes, 587 tape blocks
x ./lib/hpux64/libhbaapihp.so symbolic link to ./libhbaapihp.so.1
x ./lib/hpux64/libhbaapihp.so.1, 269768 bytes, 527 tape blocks
x ./lib/pa20_64/libhbaapifcd.sl symbolic link to ./libhbaapifcd.1
x ./lib/pa20_64/libhbaapifcd.1, 102168 bytes, 200 tape blocks
x ./lib/pa20_64/libhbaapihp.sl symbolic link to ./libhbaapihp.1
x ./lib/pa20_64/libhbaapihp.1, 96176 bytes, 188 tape blocks
x ./lib/libhbaapifcd.sl symbolic link to ./libhbaapifcd.1
x ./lib/libhbaapifcd.1, 102400 bytes, 200 tape blocks
x ./lib/libhbaapihp.sl symbolic link to ./libhbaapihp.1
x ./lib/libhbaapihp.1, 98304 bytes, 192 tape blocks
x ./bin/fcddiag, 13467 bytes, 27 tape blocks
x ./bin/fcdlist, 9494 bytes, 19 tape blocks
x ./bin/fcdutil, 514048 bytes, 1004 tape blocks
x ./bin/fcmsutil, 71652 bytes, 140 tape blocks
x ./bin/fclpdiag, 12525 bytes, 25 tape blocks
x ./bin/fclplist, 6344 bytes, 13 tape blocks
x ./bin/fclputil, 644704 bytes, 1260 tape blocks
x ./bin/tddiag, 12175 bytes, 24 tape blocks
x ./bin/tdlist, 7227 bytes, 15 tape blocks
x ./bin/tdutil, 195656 bytes, 383 tape blocks
x ./config/A6826A, 302 bytes, 1 tape blocks
x ./config/A9782A, 302 bytes, 1 tape blocks
x ./config/A9784A, 302 bytes, 1 tape blocks
x ./config/AB378A, 302 bytes, 1 tape blocks
x ./config/AB379A, 302 bytes, 1 tape blocks
x ./config/AB465A, 302 bytes, 1 tape blocks
x ./config/AD193A, 302 bytes, 1 tape blocks
x ./config/AD194A, 302 bytes, 1 tape blocks
x ./config/AD300A, 302 bytes, 1 tape blocks
x ./config/vendorfcd.conf, 124 bytes, 1 tape blocks
x ./config/vendorfclp.conf, 125 bytes, 1 tape blocks
x ./config/A5158A, 187 bytes, 1 tape blocks
x ./config/A6795A, 195 bytes, 1 tape blocks
x ./config/vendor.conf, 13 bytes, 1 tape blocks
x ./tools/fcd.pl, 18960 bytes, 38 tape blocks
x ./tools/fclp.pl, 16646 bytes, 33 tape blocks
x ./tools/td.pl, 7689 bytes, 16 tape blocks
#
# rm fcms.tar
# /opt iosca ac n
H/W Path Class Description
========================================================
root
8 cell
8/0 ioa System Bus Adapter (12eb)
8/0/0 ba Local PCI-X Bus Adapter (12ee)
8/0/0/1 slot PCI Slot
8/0/1 ba Local PCI-X Bus Adapter (12ee)
8/0/1/1 slot PCI Slot
8/0/2 ba Local PCI-X Bus Adapter (12ee)
8/0/2/1 slot PCI Slot
8/0/4 ba Local PCI-X Bus Adapter (12ee)
8/0/4/1 slot PCI Slot
8/0/4/1/0 ba PCItoPCI Bridge
8/0/4/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/4/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/4/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/4/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/5 ba Local PCI-X Bus Adapter (12ee)
8/0/5/1 slot PCI Slot
8/0/5/1/0 ba PCItoPCI Bridge
8/0/5/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/5/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/5/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/5/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/6 ba Local PCI-X Bus Adapter (12ee)
8/0/6/1 slot PCI Slot
8/0/6/1/0 ba PCItoPCI Bridge
8/0/6/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/6/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/6/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/6/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/8 ba Local PCI-X Bus Adapter (12ee)
8/0/8/1 slot PCI Slot
8/0/9 ba Local PCI-X Bus Adapter (12ee)
8/0/9/1 slot PCI Slot
8/0/10 ba Local PCI-X Bus Adapter (12ee)
8/0/10/1 slot PCI Slot
8/0/12 ba Local PCI-X Bus Adapter (12ee)
8/0/12/1 slot PCI Slot
8/0/12/1/0 ba PCItoPCI Bridge
8/0/12/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/12/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/12/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/12/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/13 ba Local PCI-X Bus Adapter (12ee)
8/0/13/1 slot PCI Slot
8/0/13/1/0 ba PCItoPCI Bridge
8/0/13/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/13/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/13/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/13/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/14 ba Local PCI-X Bus Adapter (12ee)
8/0/14/1 slot PCI Slot
8/0/14/1/0 ba PCItoPCI Bridge
8/0/14/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/14/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/14/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/0/14/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
8/120 processor Processor
8/121 processor Processor
8/122 processor Processor
8/123 processor Processor
8/124 processor Processor
8/125 processor Processor
8/126 processor Processor
8/127 processor Processor
8/250 ba Core I/O Adapter
8/250/0 acpi_node Acpi Hardware
8/250/1 ipmi IPMI Controller
8/250/2 tty Built-in RS232C
9 cell
9/120 processor Processor
9/121 processor Processor
9/122 processor Processor
9/123 processor Processor
9/124 processor Processor
9/125 processor Processor
9/126 processor Processor
9/127 processor Processor
9/250 ba Core I/O Adapter
9/250/0 acpi_node Acpi Hardware
10 cell
10/0 ioa System Bus Adapter (12eb)
10/0/0 ba Local PCI-X Bus Adapter (12ee)
10/0/0/1 slot PCI Slot
10/0/1 ba Local PCI-X Bus Adapter (12ee)
10/0/1/1 slot PCI Slot
10/0/2 ba Local PCI-X Bus Adapter (12ee)
10/0/2/1 slot PCI Slot
10/0/4 ba Local PCI-X Bus Adapter (12ee)
10/0/4/1 slot PCI Slot
10/0/4/1/0 ba PCItoPCI Bridge
10/0/4/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/4/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/4/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/4/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/5 ba Local PCI-X Bus Adapter (12ee)
10/0/5/1 slot PCI Slot
10/0/5/1/0 ba PCItoPCI Bridge
10/0/5/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/5/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/5/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/5/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/6 ba Local PCI-X Bus Adapter (12ee)
10/0/6/1 slot PCI Slot
10/0/6/1/0 ba PCItoPCI Bridge
10/0/6/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/6/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/6/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/6/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/8 ba Local PCI-X Bus Adapter (12ee)
10/0/8/1 slot PCI Slot
10/0/9 ba Local PCI-X Bus Adapter (12ee)
10/0/9/1 slot PCI Slot
10/0/10 ba Local PCI-X Bus Adapter (12ee)
10/0/10/1 slot PCI Slot
10/0/12 ba Local PCI-X Bus Adapter (12ee)
10/0/12/1 slot PCI Slot
10/0/12/1/0 ba PCItoPCI Bridge
10/0/12/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/12/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/12/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/12/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/13 ba Local PCI-X Bus Adapter (12ee)
10/0/13/1 slot PCI Slot
10/0/13/1/0 ba PCItoPCI Bridge
10/0/13/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/13/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/13/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/13/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/14 ba Local PCI-X Bus Adapter (12ee)
10/0/14/1 slot PCI Slot
10/0/14/1/0 ba PCItoPCI Bridge
10/0/14/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/14/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/14/1/0/6/0 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/0/14/1/0/6/1 lan HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter
10/120 processor Processor
10/121 processor Processor
10/122 processor Processor
10/123 processor Processor
10/124 processor Processor
10/125 processor Processor
10/126 processor Processor
10/127 processor Processor
10/250 ba Core I/O Adapter
10/250/0 acpi_node Acpi Hardware
#
# ioscan
# ioscan gets you the device of the fiber card, which you can not put into fcmsutil. Bingo, you have WWN
# ioscan -fc Cfc
H/W Path Class Description
======================================================
8/0/4/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/4/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/5/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/5/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/6/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/6/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/12/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/12/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/13/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/13/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
8/0/14/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
8/0/14/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/4/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/4/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/5/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/5/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/6/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/6/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/12/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/12/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/13/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/13/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
10/0/14/1/0/4/0 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 1)
10/0/14/1/0/4/1 fc HP AD194-60001 PCI/PCI-X Fibre Channel 2-port 4Gb FC/2-port 1000B-T Combo Adapter (FC Port 2)
# ioscan -Cfc -kn |grep dev
# ioscan -Cfc -f
/dev/fcd0
/dev/fcd1
/dev/fcd2
/dev/fcd3
/dev/fcd4
/dev/fcd5
/dev/fcd6
/dev/fcd7
/dev/fcd8
/dev/fcd9
/dev/fcd10
/dev/fcd11
/dev/fcd12
/dev/fcd13
/dev/fcd14
/dev/fcd15
/dev/fcd16
/dev/fcd17
/dev/fcd18
/dev/fcd19
/dev/fcd20
/dev/fcd21
/dev/fcd22
/dev/fcd23
# /opt/fcms/bin/fcdutil /dev/fcd23
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12DF
PCI Mode = PCI-X 133 MHz
ISP Code version = 4.2.2
ISP Chip version = 3
Previous Topology = UNINITIALIZED
Link Speed = UNKNOWN
Local N_Port_id is = None
Previous N_Port_id is = None
N_Port Node World Wide Name = 0x5001438002a24a3b
N_Port Port World Wide Name = 0x5001438002a24a3a
Switch Port World Wide Name = 0
Switch Node World Wide Name = 0
N_Port Symbolic Port Name = ttest_fcd23
N_Port Symbolic Node Name = ttest_HP-UX_B.11.31
Driver state = AWAITING_LINK_UP
Hardware Path is = 10/0/14/1/0/4/1
Maximum Frame Size = 2048
Driver-Firmware Dump Available = NO
Driver-Firmware Dump Timestamp = N/A
Driver Version = @(#) fcd B.11.31.0809.%319 Jul 7 2008
# for dev in $(ioscan -Fnk -Cfc |grep dev)
> do
> /opt/fcms/bin/fcdutil $dev
> done
##### snipping the output……####
Tags: Capacity Planning, fiber channel adaptor, forums.itrc.hp.com, Ignite-UX, npar, superdome, wwn
27 Oct 09 HP-UX Hardware: How to tell your fiber channel adapter is KIA
Important information in bold. Must run as root. Serial numbers changed to protect the innocent.
No electrons were harmed in the creation of this message.
root # fcmsutil /dev/fcd1
Vendor ID is = 0x001077
Device ID is = 0x002312
PCI Sub-system Vendor ID is = 0x00103c
PCI Sub-system ID is = 0x0012c9
PCI Mode = PCI-X 133 MHz
ISP Code version = 3.3.18
ISP Chip version = 3
Previous Topology = UNINITIALIZED
Link Speed = UNKNOWN
Local N_Port_id is = None
Previous N_Port_id is = None
N_Port Node World Wide Name = 0x50060b0000c1bd8b
N_Port Port World Wide Name = 0x50060b0000c1bd8a
Switch Port World Wide Name = 0x0000000000000000
Switch Node World Wide Name = 0x0000000000000000
Driver state = AWAITING_LINK_UP
Hardware Path is = 3/0/12/1/0/4/1
Maximum Frame Size = 2048
Driver-Firmware Dump Available = NO
Driver-Firmware Dump Timestamp = N/A
Driver Version = @(#) libfcd.a HP Fibre Channel ISP 23xx & 24xx Driver B.11.23.06 /ux/core/isu/FCD/kern/src/common/wsio/fcd_init.c:Jun 23 2006,14:05:23
Driver state = AWAITING_LINK_UP (Sure sign of a dead card)
root # fcmsutil /dev/fcd1 vpd
V I T A L P R O D U C T D A T A
——— ————- ——-
Product Description : “PCI-X 2-port 2Gb FC/2-port 1000B-T HBA ”
Part number : “AB465-60001”
Engineering Date Code : “A-4620”
Part Serial number : “PQR06501L0”
Misc. Information : “PW=25W;PCI 66MHZ;PCI-X 133MHZ”
Mfd. Date : “4651”
Check Sum : 0xf9
EFI version : “001.47”
ROM Firmware version : “003.003.154”
Asset Tag : “NA”
20 Oct 09 HP-UX Integrity Software mirror procedure
This was written by a former colleague. It is better than anything else I have seen. SEP
Mirroring a Boot Disk with LVM on HP-UX 11i for HP Integrity
Servers
The following diagram shows the disk layout of a boot disk. The disk
contains a Master Boot Record (MBR) and Extensible Firmware
Interface (EFI) partition tables that point to each of the partitions. The
idisk
command is used to create the partitions (see idisk (1M)).
Figure 6-5 Example LVM Disk Layout on HP Integrity Server
Before starting the procedure, make sure that add-on product HP
MirrorDisk/UX (B5403BA) is installed. This product is an extra-cost
product available on the HP-UX 11i application release media. For
example:
swlist -l fileset | grep -i mirror
LVM.LVM-MIRROR-RUN B.11.22 LVM Mirror
Step 1.
file.
Partition the disk using the idisk command and a partition description
a.
Create a partition description file. For example:
vi /tmp/idf
In this example the partition description file contains:
3
EFI 500MB
HPUX 100%
HPSP 400MB
NOTE
an EFI partition, an HP-UX partition, and an HP Service partition.
Boot disks of earlier HP Integrity Servers may have an EFI partition
of only 100MB and may not contain the HPSP partition.
The values in the example represent a boot disk with three partitions:
b.
Partition the disk using idisk and your partition description file:
idisk -f /tmp/idf -w /dev/rdsk/c3t1d0
c.
To verify you can run:
idisk /dev/rdsk/c3t1d0
Step 2.
the partitions. For example:
Use the insf command with the -e option to create the device files for all
insf -e -H 0/18/1/2/0.0.1.0
You should now have eight device files for this disk:
/dev/[r]dsk/c?t?d?
(This refers to the entire disk)
/dev/[r]dsk/c?t?d?s1
(This refers to the EFI partition)
/dev/[r]dsk/c?t?d?s2
(This will be the HP-UX partition)
/dev/[r]dsk/c?t?d?s3
(This refers to the Service partition)
Step 3.
disk:
Use pvcreate to make the HP-UX partition of the disk an LVMmanaged
pvcreate -B /dev/rdsk/c3t1d0s2
Step 4.
Add the disk to vg00:
vgextend vg00 /dev/dsk/c3t1d0s2
Step 5.
Place the boot files on the disk using mkboot:
mkboot -e -l /dev/rdsk/c3t1d0
Step 6.
Copy any autoboot file from the original boot disk to this one.
a.
partition to the current directory. Make sure to use the device file
with the
Use efi_cp to copy the AUTO file from the original boot disk’s EFIs1 suffix, as it refers to the EFI partition:
efi_cp -d /dev/rdsk/cntndns1 -u /efi/hpux/auto ./AUTO
b.
partition:
Copy the file from the current directory into the new disk’s EFI
efi_cp -d /dev/rdsk/c3t1d0s1 ./AUTO /efi/hpux/auto
Step 7.
volume group onto the desired physical volume. The logical volumes
must be extended in the same order that they are configured on the
original boot disk. Use the
determine the list of logical volumes and their order. For example:
Use the lvextend command to mirror each logical volume in the rootpvdisplay command with the -v option to
pvdisplay -v /dev/dsk/c0t0d0s2 | grep ’current.*0000$’
00000 current /dev/vg00/lvol1 00000
00038 current /dev/vg00/lvol2 00000
00550 current /dev/vg00/lvol3 00000
00583 current /dev/vg00/lvol4 00000
00608 current /dev/vg00/lvol5 00000
00611 current /dev/vg00/lvol6 00000
00923 current /dev/vg00/lvol7 00000
01252 current /dev/vg00/lvol8 00000
In this example, mirror the logical volumes as follows:
lvextend -m 1 /dev/vg00/lvol1 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lvol2 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lvol3 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lv0l4 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lvol5 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lvol6 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lvol7 /dev/dsk/c3t1d0s2
lvextend -m 1 /dev/vg00/lvol8 /dev/dsk/c3t1d0s2
If
lvextend fails with following message:
“m”: Illegal option
then HP MirrorDisk/UX is not installed.
Step 8.
Update the root volume group information:
lvlnboot -R /dev/vg00
Step 9.
disk and that the boot, root, and swap logical volumes appear to be on
both disks:
Display the BDRA. Verify that the mirrored disk is displayed as a boot
lvlnboot –v
Step 10.
Specify the mirror disk as the alternate boot path in nonvolatile memory:
setboot -a path_to_disk
Step 11.
text editor:
Add a line to /stand/bootconf for the new boot disk using vi or another
vi /stand/bootconf
l /dev/dsk/c3t1d0s2
where
l denotes LVM.
Tags: forums.itrc.hp.com, high capacity volume group, ia64, Ignite-UX, integrity, LVM, software mirror, superdome, system migration
09 Sep 09 Case Study: Capacity & Migration planning for a small organization
This is our first case study. The events leading up to it occur between 1998 and 2002. It is a real life case study based on my experience. For legal reasons, I can not identify the organization. It is a charity that raises now around $100 million, 92% of funds raised go to actual charitable work. 8% is overhead. IT infrastructure is overhead, even though it is critical to actually raising funds.
From 1991-2005 I worked at this charity in IT, first as a programmer analyst, then as a dba, finally becoming the backup Unix Admin in 1998 and the full time Unix Admin in 2000. The organization ran its legacy fund raising systems on a pair of D class HP-UX systems. The back end database was Software AG adabas. The user fund raising community wanted to have an sql like ability to look into the database and run queries. they wanted flexible use of strategic data. An attempt was made in early 1997 to install a sql front end, but it did not provide acceptable results.
An internal study was done and it was decided in late 1997 to migrate legacy systems to a web based front end, with Oracle as the back end database, Oracle Application Server using forms and reports to build applications. Initially no plan was made to migrate to stronger hardware, due to the assurance from Oracle that their software would run on the existing infrastructure.
By 2000 it was obvious that this was not true. Though the database server itself ran acceptably, there was not sufficient memory or disk capacity to run the application server. So I was asked to prepare a plan to migrate legacy systems. Here were the guidelines:
- To run three environments, to be described below, each with a database server, an application server and forms and reports development tools on them.
- Sandbox was to be used to test OS patches, Oracle patches, and tools upgrades. It was to belong to the systems administrator who was permitted to restart this system on short or no notice.
- The development environment was to be where the developers were to develop code. It needed to be stable and available 100% during normal development hours 8 a.m. to 6 p.m. Any changes made to his system were first to be vetted on the sandbox system.
- The production system had the same uptime requirements accept that all changes needed to be vetted first on the other two systems.
- The hardware was to be the same model for all the systems. This was defined to avoid hardware surprises. Only the production system needed to be at full capacity. the other systems were to be the same to permit realistic load testing.
- Databases would be hosted on SAN disk with an HBA fiber channel connection. Systems were to boot locally.
Overall, I thought this was a solid foundation. Some of the points were made by management, some were suggested by me.
The following basic technical requirements were developed:
- Overall database needed to be approximately 5 GB for server. Actual use hit 15 GB by 2005. This growth factor was planned.
- Oracle Server, one instance had to run on each server.
- Oracle Application server one instance had to run on each server.
- Legacy applications Natural/Software AG Adabas needed to run on each server.
- Server configuration needs to be manged and tracked responsibly.
- HP-UX bi-annual updates needed to be installed in a timely basis after quality assurance.
- The replacement cycle on hardware would be 3-5 years to maintain cost savings provided by being under warranty (First three years)
Deployment Diagram
Other Relevant facts on the decision making process.
- HP Hardware and Software agreements were running over $30,000 per year on existing infrastructure.
- Much of the cost was hardware support due to the age and near obsolescence of the hardware.
- Significant savings could be obtained by using current hardware that was under warranty.
- Systems would be configured and used to provide a disaster recovery solution.
Three vendors were picked to provide proposals. All ended up recommending HP-9000 L2000(later renamed rp5450) servers. Here are the highlights:
- rp5450 systems with 2 GB system memory.
- 146 GB dual disks to server as boot disks with software mirroring.
- 2 CPU would be installed per server.
- Memory capacity and purchase was planned to enable an upgrade to 8 GB without replacing exiting memory.
- Two HBA Fiber channel cards provided per machine to provide redundancy and fail over.
- A capital budget request was made showing that support cost savings would over the course of 4 years, completely recover the cost of the systems.
- Systems would each have a Ultirum tape drive, for locally provided backups and Ignite-UX make_tape_recovery backups as part of the DR plan.
- Systems had two Gigabit Network Interface cards.
- Systems would have a private network for use in Ignite backup, recovery and system replication.
- Systems were to be delivered with HP-UX 11.11
- HP provided RAC and UPS and PDU were specified.
How it went:
- Systems were delivered in May of 2002.
- Initial OS install began immediately. Systems were initially delivered with HP-UX 11.00. We delayed start of installation until correct media was provided.
- All three systems were installed with a base OS to insure that hardware was working.
- OS patch requirements for Oracle, security and bi-annual updates were installed on the sand box. It was decided that Ignite Golden Image would be used to replicate the sand box configuration, once a stable configuration was found.
- Significant problems were encountered with the Oracle and Oracle Application Server installations. The version was changed twice. Several major Oracle patch sets had to be installed to deal with “show stopper” bugs that were encountered.
- After the September 11 attacks in New York City in 2001, a security review was conducted and the deployment plan was modified to include improved security. Several rounds of patching and tools testing occurred on the OS level.
- In December of 2002, the application development team notified us that they were satisfied with the sandbox and asked that an Ignite image be made and transferred to the development system.
- In January-February of 2003 Imaging was done and the system was replicated. There were OS problems with the Ignite replication that took several weeks to work out.
- Several changes were requested by the development staff. They were tested on the sand box and then deployed on the development system.
- An Ignite central server was built on the sand box to handle images which were shared on NFS and available for use after booting of the sandbox Ignite configuration.
- In June of 2003 after several change cycles the configuration was approved for deployment.
- Ignite replication was completed on the production environment using the sandbox, which had been frozen for this purpose as the image template.
- In August of 2003 all legacy systems were cut over to the rp5450 systems. HR would be migrated 18 months later due to Integration issues.
- In the early of 2004 due to performance and memory use issues all systems were upgraded to 8 GB of system RAM.
- For the year 2004 there was no downtime in production systems during normal business hours.
- Weekly Ignite tape backups were taken on all systems and network based backup to shared NFS was used as a secondary DR method.
- In February of 2004 a DR test was run at the HP Performance center and we successfully migrated a sandbox image to an rp5470 server in the HP infrastructure. Legacy systems were tested and approved as functional.
Note: This document was designed entirely using the wordpress interface and a Linux system. The diagram was created with a free Linux alternative to visio called dia. The tool is in evaluation, and might be replaced. Still a pretty good start. Cost to produce this environment in licensing fees?: Zero dollars.
Tags: Capacity Planning, forums.itrc.hp.com, HP-UX, Ignite, Ignite-UX, LVM, migration, patches, system migration
